Showing results: 601 - 615 of 1308 items found.
-
CHT -
Get Control, Inc.
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
SPM -
PJ Electronics, Inc.
High Frequency Digital Surge Tester and DC Hi-Pot Tester (similar to the "SP" Model) together in a compact cabinet. Take this portable tester to your test site and accurately perform Surge, Hi-Pot, PI and Resistance Tests.
-
AWTS -
Eclypse International
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Powerohm Resistors, Inc.
The Powerohm Variable Braking Resistor Analyzer will determine what braking resistor ratings are required for your specific application. The Powerohm VBR is a portable test unit that provides selectable steps of resistance for analyzing your braking requirements for a wide range of drive horsepowers. Simply connect the VBR to your drive or braking module and let the application decide what braking resistor it needs. Once you determine the optimal resistance value for your drives peak performance, the VBR's digital readout will accurately display the true duty cycle as the application runs.
-
METRISO Series -
GMC-I Messtechnik GmbH
1) Voltage-free devices and equipment, for rugged service applications and laboratory use2) Voltage-free devices and equipment, and for testing resistance at earthing, protective and equipotential bonding conductors3) Voltage-free electrical devices and equipment, for testing resistance at earthing, protective and equipotential bonding conductors, and for testing devices under test for absence of voltage. - METRISO C only: testing floor coverings for discharge capability and electrostatic charging4) Electrical systems, machines, transformers, cables and equipment used in, for example, locomotives, street cars and ocean going vessels5) Electrical motors, machines, generators and cables
-
COMBI521EV -
HT Italia Srl
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
SAT-AC -
Shaanxi Aitelong Technology Co., Ltd
SAT-AC Battery Conductance Tester is a multi-function and portable digital data storage measurement instrument to test battery running condition and parameters quickly and precisely. It can display and record many key parameters for multi-groups like battery string and each battery cell’s voltage, conductance, connecting strip resistance, battery’s internal resistance and so on; offer the ability to distinguish battery’s condition effectively and accurately; compose with intelligent PC measurement analyzing software, user can track battery’s decay trend, and alarm beforehand to help technician and administrators process according to status.
-
6237 DLRO -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measure down to 1μΩ.● 6 ranges from 2.000mΩ to 200.0Ω.● Maximum resolution of 1μΩ.● Three test currents with over-temperature protection.● Four terminal measurement.● Protection against inadvertent connection to over- voltage. (crow bars for current and voltage)● Clear & large LCD.● Potential lead resistance and current lead resistance checks.● "Full-featured” EnerSave™ Inside.● EnerSave™ Auto-hold.● EnerSave™ Auto-off.● Rechargeable battery operated● Robust & compact.● Indicators show if reading may be invalid (RP, RC, and temperature).● "O-Ring” sealed case.
-
SKS-0510I -
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0510I fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 10kV, which can meet the severity levels of various product standards; Covers the two surge waveforms specified in the standard 1.2/50ms (short-circuit current is 8/20μs) and 10/700ms (short-circuit current is 5/320μs), and a variety of internal resistances are built-in for customer use; Two kinds of surge waveforms, and built-in a variety of internal resistances for customers to use; AC and DC samples can be tested, the rated current can reach 32A.
-
Neutronics Manufacturing Co.
The NMC 'TDR' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. 'TDR' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. 'TDR' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.
-
HH0308C -
Colluck Company Limited
Double Injection Casing. High Accuracy (basic accuracy 0.3%). 6000 count Jumbo LCD display with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 20A AC/DC. Diode and Continuity Check. Measure Resistance up to 60MΩ. Measure Temperature up to 300c. Measure Frequency up to 600k Hz
-
19050 -
Chroma Systems Solutions, Inc.
The Chroma Guardian 19050 series of Hipot Testers are comprised of three models. The Guardian 19052 is equipped for AC/DC/IR Hipot testing and insulation resistance (IR) measurements. The Guardian 19053 combines both AC and DC Hipot tests and IR measurements with 8HV scan channel capabilities. The Guardian 19054 combines both AC and DC Hipot tests and IR measurements with 4HV scan channel capabilities.
-
KRD10 series -
CME Technology Co. Ltd.
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
105/106 Series -
Analysis Tech Inc.
The 105/106 Series Event Detectors are the most versatile Event Detectors in the product line. These Event Detectors monitor the electrical resistance of up to 128 simple continuity loops, each comprised of single or multiple specimens under test. Each test specimen is continuously monitored while a selectable DC sense current is passed through each channel test-loop; resistance changes exceeding the selected threshold are recorded as an event. Minimum Event Duration, Channel Current, and Threshold Voltage settings can all be independently configured. 105 and 106 Series instruments are electrically identical, with the difference simply that the 105 offers four, 32-channel board slots and the 106 offers only one. Thus the 128-105 is equivalent to four 32-106 Event Detectors.
-
BK2020B -
BaKo Co., Ltd
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versatile. It can be set up as a stand alone machine, or used with a PC and software for access to more information, and to save the data for analysis. Either version is great on the product line but you may also use it for QA, QC and development.
